telescopeѲptics.net
▪
▪
▪
▪
▪▪▪▪
▪
▪
▪
▪
▪
▪
▪
▪
▪ CONTENTS
◄
9.2. Refracting telescope objectives: Apo
and semiapo
▐
9.3. Designing doublet achromat
►
9.2.1. Semiapo and apo lens objective examples
Within constraints given on previous page, a number of apochromatic and some viable
semiapochromatic glass combinations are possible. More than a few have
been, at some point in time, used for commercial refracting telescopes.
Following table lists examples of such objectives, from those with
small reduction in secondary spectrum, to those fulfilling the formal apochromatic condition. All achromats in comparison are assumed with nearequal
wavefront error in F and C (Δf is the
secondary spectrum in units of that in a comparable achromat, and SP
is the polychromatic Strehl for the 440670nm spectral range, photopic
sensitivity; WFE=wavefront error). Somewhat arbitrarily, objective's
mode of correction is classified based on its secondary spectrum vs.
that in the standard achromat as enhanced achromat (EA) if less than
twofold reduced, semiapochromat (SA) if twofold to ninefold reduced,
and apochromat (A) if reduced by tenfold or more. According to their polychromatic Strehl, objectives range
from sensibly perfect (SP>0.95)
to fair (0.7<SP<0.8)
depending on two variables: their mode of correction, and their relative
aperture (glass dispersion: ● "normal" i.e.
common, ● partly
abnormal, ●
"abnormal" i.e. very low dispersion).
# 
D
(mm) 
f 
GLASS
RADII / THICKNESS // SEPARATION
(mm) 
Δf1 
RMS WFE
(RATIO v. ACHR) 
SP
(ACHR) 
Element 1 
Element 2 
Element 3 
e 
(F+C)/2 
g 
r 
1 
100 
12 
BAK1
789, 267/11//0.6 
BASF52
277, 1430/6 
 
.79
EA 
.007 
.22
(.76) 
1.2
(.85) 
.36
(.82) 
.86
(.81) 
2 
150 
10 
BK7
910, 330/16//1 
KZFSN4
339.5, 1818/9 
 
.75
EA 
.017 
.37
(.71) 
2
(.78) 
.69
(.74) 
.75
(.71) 
3 
100 
15 
BK7
880, 187.3/11//0.15 
KZFN2
188, 3900/7 
 
.73
EA 
.003 
.18
(.78) 
.88
(.78) 
.32
(.77) 
.89
(.84) 
4 
150 
15 
BALF5
1494, 372/17//0.7 
BASF52
391, 1800/9 
 
.72
EA 
.017 
.25
(.73) 
1.35
(.80) 
.40
(.64) 
.83
(.77) 
5 
150 
12 
BAK1
1000, 310.4/17//2.1 
KZFSN4
31, 6630/9 
 
.47
EA 
.017 
.20
(.46) 
1.26
(.59) 
.28
(.36) 
.86
(.73) 
62 
150 
6.5 
BAK1
484, 1440/12 
KZFSN4
1440, 203.8/8 
BAK1
203.8, 7300/16 
.47
EA 
.020 
.37
(.37) 
2.3
(.45) 
.54
(.39) 
.76
(.61) 
72 
150 
10 
BK7
1862, 365.4/14 
KZFS1
365.4, 365.4/6 
BAFN10
365, 1343/14 
.15
SA 
.018 
.07
(.13) 
.56
(.22) 
.084
(.09) 
.94
(.71) 
82 
150 
8 
BAK1
1711, 235/16 
KZFSN4
235, 277/9 
BAFN10
277, 1430/14 
.13
SA 
.018 
.10
(.24) 
.85
(.40) 
.10
(.13) 
.87
(.67) 
9 
150 
15 
BALF4
603, 244.25/18///0.09 
KZFN2
243.75, 166.6/6.2//6.4 
K7
172.4, 927.7/16 
.1
A 
.015 
.039
(.11) 
.52
(.31) 
.021
(.034) 
.954
(.77) 
10 
127 
9 
KF3
551, 192/8//0.15 
FK01
192.2, 13600/12 
 
.22
SA 
.006 
.10
(.21) 
.62
(.26) 
.18
(.20) 
.93
(.72) 
113 
100 
7 
FK51
390, 127/15//0.6 
ZKN7
127, 1464/7 
 
.01
A 
.046 
.10
(.20) 
.24
(.10) 
.13
(.15) 
.83
(.71) 
ZKN7
348, 100.5/6//0.6 
FK51
100.5, 2727/15.5 

.059 
.10
(.20) 
.23
(.10) 
.11
(.13) 
.78
(.71) 
123 
100 
7 
FPL53
384, 156/14//0.37 
ZKN7
159, 750/6 
 
.01
A 
.024 
.063
(.13) 
.15
(.06) 
.067
(.08) 
.93
(.71) 
ZKN7
278, 117.1/6.//0.46 
FPL53
115.7, 3080/14 
 
.029 
.066
(.13) 
.16
(.06) 
.062
(.07) 
.92
(.71) 
13 
100 
7 
ZKN7
386, 204/7 
FK51
204, 178/15 
ZKN7
170, 1500 
.01
A 
.010 
.050
(.10) 
.11
(.05) 
.077
(.09) 
.97
(.71) 
143 
100 
7 
CaF2
379, 166/13//0.75 
K5
169.7, 699//6 
 
.07
A 
.022 
.073
(.15) 
.15
(.06) 
.078
(.09) 
.93
(.71) 
K5
264, 121.2/6//0.22 
CaF2
119.3, 3544/13 
 
.022 
.074
(.15) 
.155
(.06) 
.081
(.09) 
.92
(.71) 
15 
100 
10 
ZKN7
396, 165.3/6//0.4 
FPL53
163, 4400/14 
 
.01
A 
.005 
.025
(.07) 
.06
(.035) 
.020
(.033) 
.99
(.78) 
16 
100 
10 
K5
378, 172/6//0.9 
CaF2
169.3, 5060/13 
 
.07
A 
.004 
.034
(.1) 
.07
(.04) 
.041
(.066) 
.984
(.78) 
172 
140 
7 
K10
479, 277/12 
FPL53
277, 359/21 
BK7
359, 1252/12 
.124
A 
.011 
.052
(.075) 
.33
(.1) 
.066
(.054) 
.955
(.64) 
182 
140 
7 
ZKN7
420, 222/10 
FPL53
222, 486/19 
ZKN7
486, 1880/10 
.01
A 
.013 
.040
(.058) 
.17
(.05) 
.068
(.056) 
.970
(.64) 
192 
140 
7 
K7
448, 268/10 
CaF2
268, 360/21 
K7
360, 1300/10 
.03
A 
.012 
.043
(.062) 
.16
(.047) 
.045
(.037) 
.965
(.64) 
20 
130 
7.7 
FPL53
2380, 262.2/12///22.9 
BSL7
239.8, 2580/7//1 
FPL53
444, 926/11 
.025
A 
.003 
.029
(.048) 
.029
(.017) 
.065
(.032) 
.987
(.64) 
21 
140 
7 
ZKN7 580,
293/9//1
FPL53
293, 2500/13//920 
920mm
interspace 
FPL53
537, 227.7/12//
1
ZKN7
232.1, 1170/7 
.01
A 
.003 
.033
(.048) 
.06
(.017) 
.027
(.032) 
.983
(.64) 
1Measured as the
longitudinal separation between the common C/F focus and best
eline focus, in units of that in a comparable standard achromat
(not a reliable indicator of chromatic correction in the
presence of significant spherochromatism)
2Triplets with two
pairs of conforming inner radii and zero lens separation can be
assumed to be oiled triplets; for simplicity, oil medium is
omitted, with zero lens separation (it generally has a minor effect)
3Top specs are for
the ED glass element (the positive one) in front, bottom for ED
glass in rear; in general, the latter requires more strongly
curved inner radii, with more spherochromatism
4Approximately; based
on the offsetting RDP differentials for K10 and BK7 vs. FPL53,
the former nearly four times greater, but the latter in a nearly
twice stronger lens, resulting in an effective RPD differential
of roughly twice that of BK7 
TABLE 12:
Examples of lens objectives with enhanced chromatic correction vs.
standard doublet achromat, starting with combinations of normal and
partly abnormal glasses, toward objectives using abnormal (very low
dispersion) glasses:
#1, 2, 3, 4
 enhanced doublet achromats with one somewhat abnormal glass;
#5  further enhanced
doublet achromat, with less than half the secondary spectrum of the
standard achromat (#3 is the Zeiss AS objective),
#6  triplet achromat with the same glasses as
previous, having only slightly more of higherorder spherical in the optimized
wavelength (it would have made the doublet useless at this fratio);
#7  triplet using one of
glass combinations in the early AstroPhysics triplets, approaching 0.95
Strehl at
f/10;
#8  triplet with similar
correction level at
f/8; note how much use of different
glass for the second, positive element, with an offsetting RPD
differential versus first element, further reduces secondary spectrum
#9  an early triplet
form (Zeiss B type), modification of the Taylor's photovisual triplet;
#10  older Meade doublet
apo;
#11, 12  two apo
doublets with similar reduction in secondary spectrum, but with
significant variation in the level of spherochromatism due to their
respective Abbe differentials,
#13  same glasses as in #11, but in a triplet form, greatly
reduce spherochromatism; #14
 calcium fluorite doublet at the same focal ratio as #1113;
#15 and #16  doublets
with the same glasses as #12 and #14, respectively, become practically
perfect at
f/10;
#17  triplet with glass
combination used in TEC's 140
f/7 apo;
#18, 19  triplets with
identical aperture/fratio
and different glass combinations;
#20  Takahashi TOA type
triplet #21  same aperture/�ratio
objective with identical glasses as #18 triplet in the Petzval
arrangement
Some of the above objectives do not have the optimum, even acceptable
relative aperture if the principal criteria is highest level of
chromatic correction. The purpose is to illustrate the limitations of
particular type of objectives. Numerical data is graphically illustrated
by the respective longitudinal aberration (LA) plots and ray spot plots (FIG.
149; note that the black circle is the Airy disc in the eline,
which is of
constant size for any given objective; variation in its size is due to
the need to fit blurs of often very different sizes together).
Most of LA graphs for doublets and fast triplets show
mixture of 6th
and 4th order spherical aberration.
FIGURE 149: Secondary spectrum and spherochromatism in the objectives from
Table . While formally defined as the longitudinal separation between
the common red blue (F/C) focus and green (eline), all paraxial (here,
on the horizontal scale; note that the size of scale varies), actual
location of these foci is shifted due to the presence of
spherochromatism. In general, the paraxial blue focus is shifted closer,
and the red focus about as much farther away from where that common
focus would have occurred. Obviously, if they would be
nearly coinciding, the wavefront error would have been significantly
greater in the shorter wavelength, more so due to it being overcorrected
(when reading these plots, it is important to keep in mind that all the
zones at the aperture radius  represented as the vertical scale  focus
at the horizontal scale; the foci are merely projected up to the zonal
height, forming the
longitudinal aberration plot).
The magnitude of F/C
paraxial separation for given level of spherical aberration is somewhat
arbitrary; it is often such that F and Cline ray spots are
nearly equal in size. Since in that case the wavefront error is greater
in the F  not the best mode considering that eye sensitivity is higher
in the blue line, even in the photopic mode, and more so toward mesopic
mode  refracting objective here are generally brought to a near equal
wavefront error in F and C.
Plots for objectives
#15 show F and C lines
clearly separated from the
eline, indicating the presence of secondary spectrum (these five
objectives only show these three lines, since r and ,
particularly, g, are far enough to squeeze F, C and
e too close together on this image scale). Secondary spectrum is
significantly reduced in #6,
a fast triplet using somewhat abnormal short flint for its central
element (typically for short flint combinations, the violet end runs
away). It is still more reduced in
#7, a triplet combo of
the early NASA Christen triplet combo;
#8, also an Astrophysics'
triplet combo from the 1980s, uses another short flint, originally made
for NASA (reportedly, a bit better than Schott's KZFSN4 available today
only as a special melt); it does form a typical apo C/F/e crossing
at about 76% zone, but some residual secondary spectrum is still
evident, since F and C paraxial foci are at unequal
separation from paraxial e focus (by slightly strengthening the
negative power, F could be brought to coincide with C but,
since C is farther away from e than F, this common
focus would be be falling somewhat behind e). In
#9, an early Zeiss
triplet, secondary spectrum is nearly eliminated, but higher order
spherical creeps in due to the strong surface radii, even at
f/15. A more recent doublet, the older Meade
"apo" at #10, with
Hikari's FK01 ED glass (nearequivalent to Ohara FPL51), still has some
relatively significant secondary spectrum (at 127mm
f/9 its is still quite close to 0.95 visual
polychromatic Strehl). At #11,
very similar Schott FK51 ED glass, in combination with a common crown,
has secondary spectrum all but eliminated, but clearly shows
spherochromatism at
f/7 (both combinations, with the ED first,
and following the crown, are shown). Using ED with higher Abbe number
(i.e. lower dispersion), like FPL53 (#12),
or calcium fluoride (#14),
reduces spherochromatism, and even more does using the triplet form (#13).
Spherochromatism with these same glasses in a doublet form is, as
expected, significantly reduced at slower
fratios (#15,
16). Larger fast objectives require triplet form for good
chromatic correction: #17
shows plots for TEC 140mm f/7 triplet combination optimized for visual
mode (the actual instrument is said to have 0.92 polychromatic Strehl,
which implies that the violet is being pulled closer, at the expense of
the optimum F/C correction, to improve its photo/CCD performance). If
such triplet was made with ZKN7 for the 1st and 3rd element (at a small
increase in the glass cost), secondary spectrum is practically
eliminated, but the overall gain is relatively small, because it is
spherochromatism, i.e. spherical aberration in nonoptimized wavelengths
that causes most of the chromatic error (#18).
For the same reason, replacing FPL53 with fluorite and ZKN7 with one of fluorite's matching crowns
(K7), produces nearly identical correction (#19).
With somewhat wider air gap between the front and second lens element,
it is possible to practically eliminate spherochromatism (#20,
Takahashi TOA type triplet). Using the same glasses as in #18 in a 2doublet Petzval arrangement reduces spherochromatism by reducing
the lowerorder residuals due to index
variations and eliminating higherorder spherical, but it is still
present (#21).
However, the
added bonus of the Petzval is the flattened image surface (which is
curved to about 3540% of the focal length in doublets and triplets);
residual astigmatism left in for that purpose is still less than half
the astigmatism of the triplets.
ASPHERIZING FOR REDUCTION OF HIGHERORDER SPHERICAL
IN LENS OBJECTIVES
All above systems utilize only spherical surfaces.
While it is a plus with respect to ease of fabrication, it is also a
limitation with respect to correction of higher (6th) order spherical
aberration (secondary astigmatism is generally negligible, and secondary
coma low in comparison, easy to reduce to negligible by balancing it
with the primary coma). Aspherizing a surface does not appreciably
change the ray height on it, but it does change surface profile,
bringing it either closer or farther away (depending on the sign of the
aspheric) from the 6th order surface approximation (FIG.
37). When significant, higherorder spherical affects
not only the level of correction in the optimized wavelength, but also
adds to spherochromatism (since it changes surface profile, it also
affects longitudinal chromatism, and may require slight adjustment in the
radii power balance). Removing 6th order spherical by way of aspherizing
also tends to lessen the violet 4th order error, producing better color
balance. The effect is generally small, and may be marginally
significant in oiled objectives, due to the stronger aspherization
required to remove 6th order spherical aberration on an oiled surface.
The manner in which aspherization affects
spherochromatism is somewhat different in triplets vs.
doublets.
In doublets, the typical form of secondary spherical is undercorrection.
With it uncorrected, and with primary spherical corrected in the optimized
wavelength, a doublet is more undercorrected in the red (which is
undercorrected in primary spherical for zero primary spherical in
optimized wavelength, thus the two aberrations add up), while to some
extent balanced in the blue (which is overcorrected for zero primary
spherical in optimized wavelength, hence opposite in sign to that of
secondary spherical). When this residual secondary spherical is balanced
with primary spherical of opposite sign (overcorrected) by a slight
adjustment in one of the inner radii, it can be minimized only in one,
optimized wavelengths, while added primary overcorrection reduces error
in the red (tending to produce predominantly higher order spherical,
since added primary overcorrection partly offsets its primary undercorrection
component) and increases it in the blue/violet, by enlarging its primary
overcorrection component. Taking as an example the FPL53/ZKN7 doublet (#12),
those two stages are shown as first and second from left, respectively.
Since most of the lens' secondary spherical is generated by the slight
excess on the second vs. third surface, it can be eliminated by slightly
aspherizing either of the
two radii (prolate ellipsoid for the second, and oblate for the third
radius). To compensate for the induced primary spherical imbalance, one
of the other two surfaces, with the relatively low secondarytoprimary
aberration ratio, needs to be aspherized. The result is shown on the
third plot. Removing secondary spherical by aspherizing had no
appreciable effect on spherochromatism. The only significant change is
in the correction level in the optimized wavelength, but since it is
sufficiently low with all surfaces spherical, aspherization is not worth
the extra cost. Even if the 8TH order residual (about 0.05 wave RMS,
minimized to 0.012 wave by balancing it with the opposite in sign
primary spherical) is removed by putting a Schmidttype aspheric on one
of the surfaces, the overall correction is not significantly better.
In the typical triplet, the residual secondary
spherical is most often overcorrected, while for cancelled primary
spherical in the optimized wavelength, the red and blue/violet are, like
with the doublet, undercorrected and overcorrected in the primary
spherical, respectively. Hence balancing this residual overcorrected secondary
spherical by adding primary spherical of opposite sign now lessens the error
in the red, producing a partially balanced 6th.4th order aberration, while increasing it in the blue/violet. Since the latter
typically already has significantly larger error, this creates more of a
red vs. blue/violet imbalance than in the doublet. Thus lessening this
imbalance through removing the lens' secondary spherical residual by aspherizing one or two surfaces will generally produce more of a
beneficial effect on overall correction than in a doublet. The
difference may and may not be significant.
It can be
illustrated on the ZKN7/FPL53/ZKN7 triplet (#18). While triplets with
equal pairs of inner radii are usually intended for oiltype lens, they
were given above as a cemented objective, without spacing and oil specs,
because small spacing of this type (usually a small fraction of a mm),
with or without oil, does not appreciably change lens' output (in this
particular case it only added about 1/20 wave PV of primary spherical,
which can be corrected by a slight bending of the inner two radii pairs,
to 220/496mm). That's
because the aberrations at the inner four radii, which are dominant,
tend to change evenly, in proportion. However, the conics that works
with airspaced triplet (which are nearly identical for the cemented as
well) will not work with the oilspaced one. For instance, this
particular triplet if airspaced will have its higherorder spherical
aberration excess nearly eliminated by putting 0.03 conic on the second
surface, and the primary spherical induced by that offset by putting
0.225 conic on the front surface. And if lens' interspaces is filled
with oil, the needed conics are 0.5 and .538 for the third and first
surface, respectively (third surface requires significantly less
aspherizing in this case). The output is also very different for the
airspaced and oiled objective, as shown below (since OSLO Edu doesn't
list lens oils, prescription uses Schott KF6 crown which has similar
refractive index to some commonly used oils).
Compared to the nonaspherized airspaced lens with all other specs
identical, removing higherorder spherical with aspherization did
somewhat reduce the error in the blue vs. red, but only by about 10%.
Thus removing 6th order spherical aberration residual with aspherization
wouldn't be justified with this particular lens, less so considering
that it would require double aspherization. The results are, however,
very different with the oiled lens. Due to the refraction being very
much suppressed by the higher refractive index in the interspace (1.52
for KF6 vs. 1 for air), the inner surfaces act as of significantly
weaker radii, requiring a higher nominal conic for canceling the 6th
order spherical imbalance. But the required change of surface profile to
remove 6th order spherical here also affects spherochromatism in the 4th
order spherical, simultaneously removing both, 6th and 4th order
spherochromatism. The result is a nearly zerospherochromatism lens,
which is at
f/7 better corrected than TOAtype lens at
f/7.7 (note that a slight change in radii was
required to offset the effect of aspherization on longitudinal
spherochromatism; it increased the focal length about 1%).
Unfortunately, putting 0.5 conic on such a strongly curved surface (�/0.8
if mirror)  more so considering it is a hard to work with glass  is highly unappealing in terms of
related cost. The alternative of aspherizing nonFPL53 surfaces (0.4
conic on the first and 39 last surface) would eliminate the 6th order
residual, but with no reduction in spherochromatism.
However, the manner in which the 6th order excess is generated varies
with the glass combinations and lens configuration. The above example
is not a "good candidate" for aspherization, with double aspherization
required, and little to gain from it. The reason for double
aspherization here is that one surface needs to be aspherized in order to
minimize 6th order spherical, but this cannot be compensated for by
bending the mid element, due to the 6th order spherical aberration total
for the two inner surface pairs remaining significant. Thus
compensatory aspherization of another surface is necessary. This may
change with different glass combinations, different lens arrangement, or
both. For instance, this same glass combination but in the
positivenegativepositive (PNP) element arrangement  hence with the
matching glass sandwiched between two ED elements  only requires singe
aspherization, as shown below, can have its 6th order spherical
aberration residual eliminated by aspherizing a single nonFPL53
surface, with the primary
spherical induced by aspherizing neutralized by the aberration of
opposite sign induced by reshaping the mid element (first and last
radius are changed in order to minimize coma which was to a smaller
extent also induced by reshaping the mid element). As the LA graphs and
RMS numbers show, spherochromatism is significantly reduced with
aspherizing (note that F/C correction can be made still better, by
slightly weakening the positive vs. negative power, i.e. shifting red to
the left, and blue/violet to the right, at a price of g/r error
increase). The negatives are the relatively strong aspheric required,
and two ED glass element needed in the PNP triplet arrangement.
In order to be viable for aspherization, an NPN triplet has to use
different matching glasses. Here's an example where the matching crowns
are also Ohara, as well as the glass used to simulate the oil (nearly
identical to the Schott KF6 in the index and dispersion).
The aspherized LA plot is very similar to that of the published plot for
the AP 140mm
f/7.5 EDF triplet apo (in the published
lines, which are somewhat different, with the 460nm instead of 436nm, no
706nm and unspecified line in between e and F). There is
no way to know how close are these specs to the actual ones  except
that we know it is a NPN arrangement with FPL53 as the mid element  but
this fast and large triplet had to be aspherized in order not to show
the 6th order residual. While the spherochromatism is somewhat reduced
in the aspherized version, the gain is rather small. The red/blueviolet
imbalance is also slightly smaller with aspherizing (which should result
in a slightly whither whitestar image), but even both combined make for
a rather small difference. It is important to note, though, that the
gline LA is 25% smaller in the aspherized version, hence optimizing for
the violet would give the aspherized version a slight edge in this
respect. Still, the only rationale for aspherizing here would
be to bring the lens as close to perfection as possible (note that the
mid element in the AP lens is not equiconvex  the first surface is
more strongly curved, which may make it possible to aspherize only the
5th surface, perhaps less than in this example  but the point here is
to examine the gain from aspherizing, which should remain similar,
considering that the aspherized version's LA graph is nearly identical
to the published data for the AP lens).
However, this is only so in the context of the error magnitude expressed
as RMS wavefront error, or corresponding Strehl. Neither accounts for
the differences in the pattern of the disturbed energy and its possible
effects. Looking from the standpoint of distribution of the energy lost
from central maxima, the benefit from aspherization can be significant
even in this case (as well as in the case of the
doublet example). Even if
the RMS error decrease is relatively small, the effect on
ensquared energy
just from replacing balanced secondary spherical  and to a smaller
extend its partially balanced forms  with primary spherical at best
focus can result in appreciable benefit in imaging applications. It
could also be beneficial in visual use, since balanced 6th/4th order
(i.e. secondary) spherical aberration throws energy lost to the Airy
disc significantly farther away than primary spherical of similar
magnitude (FIG. 98). This generally
makes the wavelengths with the largest error  commonly the blue/violet
 more readily visible as a separate fringe coloration, particularly on
bright objects. While contrastwise this shouldn't have significant
effect if the magnitude of aberrations remains similar, it could still
produce a noticeable cosmetic, i.e. color purity improvement in such
instances. It could also enhance imaging performance in these
wavelengths. Combined with the possible reduction in the 4th order
spherical due to aspherization, it could produce tangible overall
benefit in the performance level.
Common glass apochromats
The modern choice of glasses allows achieving apochromatic
correction in midrange focal ratios even without the use of ED glasses.
For some reason, the market did not make a serious move to that
direction, but it could happen. ED glass is not a must for apochromatic
correction; what it requires is simply a large enough Abbe differential
and negligibly small relative partial dispersion (RPD) differential.
There is a relatively few nonED glasses that can be used to that
effect, and probably the best positioned is the Schott NKZFS2 (as shortflint, not a
"normal" glass, but the main criteria here is the price, as given in the
latest OSLO Edu glass catalog). Being in the latest Schott catalog, it should have sufficient quality for
the purpose. On a diagram below, it is positioned center left. For a
more complete picture, glasses from other companies are included, but
those marked are mainly Schott, and a few others used in the examples.
Can it produce a 6" f/15 apo triplet combined with ordinary crowns like
BK7 and K5? You bet.
With g and r lines below λ/2, and very low error in e,
F and C, this objective satisfies the "true apo"
criterion. Average cost per glass element is 1.13 in units of the BK7
cost. The higher order spherical aberration residual can be reduced if all four inner
radii are allowed to be unequal: R16 1080/424/429/321/317/4000, interspaces 0.65mm.
The eline RMS goes down to 0.0065 wave (0.998 Strehl).
Similar performance can be achieved with a simpler combination, with
NSK5.
With NSK5 being 1.6 times the BK7 price, it comes out at 1.4 times per
lens element. Unlike the previous combination, using one matching
element with a relatively significant RPD differential and offsetting it
with the other element of similar differential of opposite sign, this
lens combine two glasses with a small RPD differential, for the
negligible secondary spectrum. If their Abbe differential was larger, it
would work with the faster fratios as well.
Or, going farther left, for a glass with larger Abbe differential, like
NPK51, would make possible faster objectives, whether in combination
with NSK5, or using it for both positive lenses. At 6" f/8, such
combination is just short of a true apo, and the cost per element is
that of BK7 glass.
The only line running away is the deep red r, which may be
correctable in a combination with a different glass for the second
positive element.
The NPK51 vs. NKZFS2 Abbe differential is large enough to work well in
a doublet too. It doesn't quite make it for the "true apo" at f/9, but
it would at f/10.
At f/9 it doesn't satisfy the "true apo" requirement, being a bit short
of it in the blue F and deep red r lines, but it would at
f/10. All at the cost equal to that of BK7 glass.
Can NKZFS2 do it at f/12 with, say, Chinese glasses. Almost (but this
is not necessarily best possible combination, so the answer could be
"yes").
The lens is just short of the "true apo" minimum in the r and
F line. The two Chinese crowns are a bit more expensive than the
Schott's, coming out to 1.4 times the BK7 cost per lens.
Other current Schott short flints also can achieve the "true apo" level
in fratios faster than f/10. For instance, NKZFS11, being somewhat
higher on the RPD diagram than NKZFS2, does not have potential mating
glasses with as much of Abbe differential, but still can produce similar
performance level, either with glasses of a similar RPD, or combining
it with a pair of glasses of significantly different RPD differentials of opposite
sign, nearly offsetting one another for cancelled secondary spectrum.
In combination with NSSK8, priced at 1.7 times the BK7, triplet
objective has 0.96 polychromatic Strehl at f/9, and also passes the
"true apo" g/F/e/C/r criterion.
In a doublet, this combination has the "true apo" color correction at
f/15, but due to the residual higher order spherical only 0.95 Strehl in
the central line, and 0.92 polychromatic Strehl. As an example of using
glasses with significantly different RPD from NKZFS11 that offset one
another, a NSK5/NKZSF11/LF5 combination has 0.934 polychromatic Strehl
at f/9, and passes the "true apo" criterion at f/10.
_____________
Summing it up, the magnitude of secondary spectrum is only a part of the
equation  and not necessarily the most important one  when it comes to
the chromatic correction level of refracting objectives. Its existence
itself does not prevent achieving sensibly perfect chromatic correction.
Even the standard achromat will do if left long enough, and it only gets
easier with glass combinations that have it reduced or even eliminated.
But as the secondary spectrum diminishes, another chromatic aberration 
spherochromatism, or variation of spherical aberration with wavelength
(also called tertiary spectrum)  takes the front seat. In
general, it increases exponentially with the relative aperture (D/�),
and in proportion with the aperture diameter. Thus, a zero secondary
spectrum does not necessarily mean great chromatic correction, and
could, in fact, accompany a less than perfect, or substandard one.
Similarly, the number of color crossings itself does not guarantee high
level of correction. It does imply that the wavelengths over the visual
range are packed tightly together, but what will ultimately decide the
level of chromatic correction is the magnitude of spherochromatism. And
it is, at any given focal ratio and aperture, mainly determined by the
form of objective (doublet, triplet, quadruplet, Petzval) and Abbe
differential of the glasses combined.
Using adjective apochromatic in any form to imply the level
of chromatic correction is fundamentally inappropriate, since its
primary meaning is for the specific mode of chromatic correction.
Apochromatic objective can be poorly color corrected and, on the other
side, standard achromat can be sensibly perfect. Does that make them
"fake apo" and "fake achromat"? Of course not. They still have those
same respective modes of color correction. What determines their actual
error level is not their color correction mode, but the size of
aberration over the wavelength range. And it should be expressed in the
standard form for all aberrations, the RMS wavefront error and Strehl
ratio. Combined with the particular spectral sensitivity of the
detector, they determine the actual diffraction intensity at the focus
point, the polychromatic Strehl. According to generally accepted
criteria for visual observing, refracting objective is sensibly perfect
if its polychromatic Strehl exceeds 0.95.
◄
9.2. Refracting telescope objectives: Apo
and semiapo
▐
9.3. Designing doublet achromat
►
Home
 Comments 